目的：
\begin
Opdag hvorfor 18 millioner mennesker verden rundt stoler på Overleaf med deres arbejde.
\documentclass[%
aps,% javascript:void(0);
prl,%
%12pt,%
%twocolumn,%
%preprint,%
reprint,%
amsmath,%
amssymb%
]{revtex4-1}
\usepackage{graphicx}% Include figure files
\usepackage{dcolumn}% Align table columns on decimal point
\usepackage{bm}% bold math
\usepackage{natbib}
\usepackage{CJK}
%
\begin{document}
\begin{CJK*}{UTF8}{bsmi}
% 從這裡開始編輯 %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\title{實驗一 基本測量} % 實驗名稱
\author{黃雅柔（10413126）} % 組員一的名字與學號, 主筆者擺第一位作者
\affiliation{化學系ㄧ年級} % 組員一的系級
\author{汪函儀（10425154）} % 組員二的名字與學號
\affiliation{化學系ㄧ年級} % 組員二的系級
\begin{abstract}
目的：1. 熟悉分析實驗數據的方法，測量並分析誤差。 \newline
2. 學習有效數的處理。 \newline
3. 了解螺旋測微器(Micrometer)的操作方式並用以測定微小物體的厚度或直徑等。 \newline
4. 了解游標尺(Vernier caliper)的操作方式並用以測量塑膠管的深度及內、外徑。
\end{abstract}
\maketitle
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\section{實驗原理}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
1.有效數：\newline
紀錄實驗數據或計算結果時，要使用準確數加一位估計數。準確數視儀器所能測量的最小單位而定。例如：最小刻度為mm的尺測量出的結果必須記錄到0.1mm。並將其他多餘的位數「四捨六入五取偶」。\newline
2.實驗誤差：\newline
A. 系統誤差：儀器誤差(儀器精度受到限制)\newline
人為誤差(實驗者所造成的)\newline
環境誤差(受到溫度、濕度、氣壓等影響)\newline
B. 隨機誤差：隨機、偶然的誤差，觀測者無法控制之，它是一種機率問題。增加實驗次數再使用統計理論來處理方可得出最接近的「真確值」。\newline
3.統計理論：
\ref{math1.png}
\begin{figure} % 插入圖檔
\includegraphics[width=4cm]{math1.png}
\caption{\label{fig1}光槓桿儀器三角座 }
\end{figure}
% 使用 \ref{} 來引用 \label 標籤
%ㄓㄤ%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\section{實驗儀器}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
光槓桿、米尺、望遠鏡(附十字線)、玻璃板、定位玻璃
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\section{實驗方法與步驟}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\begin{enumerate}
%步驟一
\item 將光槓桿置於定位玻璃板上，如圖（四）所示，圖內三個圓圈表光槓桿之三個腳。
%步驟二
\item 距光槓桿約1.5公尺處，安置望遠鏡及直尺，記錄光槓桿到米尺之距離D。
\end{enumerate}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\section{數據分析}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
表\ref{tab1}是用光槓桿方法量測不同數目的紙張所得的數據，... ...
\begin {table}
\caption {用光槓桿量測紙張厚度} \label{tab1}
\begin{center}
\begin{tabular}{ | c | c| c | c | } \hline
紙張張數 & l$_1$(cm) & l$_2$(cm) & $\Delta$ l(cm) \\ \hline
1 & 10.51 & 11.51 & 1.00 \\ \hline
2 & 10.51 & 12.51 & 2.00 \\ \hline
\end{tabular}
%\caption {Should be a caption}
\end{center}
\end {table}
根據表\ref{tab1}的結果，我們將量測厚度對紙張張數作圖，得到圖\ref{fig2}。從線性擬合的斜率可以得到平均一張紙的厚度為 1.0 cm。
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\section{結果與討論}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
從表\ref{tab1}的結果我們知道一張紙的厚度為 1.00 cm。... ...
這個數據和用螺旋測微器得到的結果相比，... ...
實驗結果誤差不大，可見用光槓桿可以準確的量測物體的微小厚度變化。... ...
\end{CJK*}
\end{document}